|
 
Contact Web Cleaning Tacky Roll
|
|
|
Deuce Contact Cleaning / Tacky
Roll
|
|
The 2-Roll Deuce Contact
Cleaning / Tacky Roll Cleaning System is designed for cleaning just
one web surface and is the most basic of all the narrow web cleaners.
It consists of one contact cleaning roll (CCR) and one tape roll.
Product waste results from dust and particulate
contamination on surfaces of film, paper, or other substrates. Small
particles adhere to the web surface due to static charges, moisture,
etc. These particles lower your product quality, cost you money, cause
production loss and dissatisfied customers.
Simco’s Narrow Web Contact Cleaning Systems can remove
particles from 20 down to 1 micron. Using CCRs in a nip configuration,
the CCR applies from 0.5 to 2 psi pressure on the web, squeezing out
the boundary layer of air. Performance evaluations reveal a cleaning
efficiency of 97% of particles down to 10 micron in size and removal
of most particles to 1 micron in size. |
|
|
|
QuadClam and HexClam Contact Cleaning
|
|
These 4 and 6 roll contact cleaning / tacky
roll cleaning systems remove particulate from both the top and bottom
web-surface. The QuadClam and HexClam Web Cleaning Systems allow the
top-half of the cleaner assembly to open and the tape-roll to slide
out on a drawer. This greatly facilitates tape maintenance and web
threading. The HexClam is available to 24” and the QuadClam is for
30”– 60” widths.
Features:
► Quick release gudgeons for quick removal of tapes.
► Air cylinders engage & separate rolls.
► Anti-Static bar and power supply for easy particulate removal
► Operator panel remotely mounted
► Speed: 500 fpm on narrow webs and up to 500 fpm on wide
► Rugged SS/AL construction with Plexiglas safety covers |
|
|
|
QuadClean and HexClean Contact Cleaning
|
|
The QuadClean and HexClean Contact Cleaning
/ Tacky Roll Cleaning Systems are basic 4-roll and 6-roll assemblies
for both top and bottom web-surface cleaning. The HexClean is
available to 24” wide and the QuadClean for 30” to 60” widths.
Features:
► Quick release gudgeons for quick removal of tapes.
► Air cylinders engage & separate rolls.
► Anti-Static bar and power supply for easy particulate removal
► Operator panel remotely mounted
► Speed: 500 fpm on narrow webs and up to 500 fpm on wide webs
► Rugged SS/AL construction with Plexiglas safety covers
|
|
|
|
Vac-N-Tac Comb. Web Cleaning System
|
|
SIMCO’s patent pending Vac-N-Tac Narrow
Web Cleaning Systems are precision engineered to continuously clean
paper, film or foil substrates of web thickness as thin as .001".
Particles down to 1 micron in size are removed in a
3-stage process using static elimination, vacuum and contact cleaning
rolls (CCR). The Vac-N-Tac Web Cleaner offers better value and higher
performance than just contact cleaning systems, ultrasonic cleaners or
traditional vacuum collection. Specifically designed to fit into lines
with space constraints, the unit vacuum cleans the majority of
particles before the CCR cleans the web. Performance evaluations
reveal a cleaning efficiency of 97% of particles down to 10 micron in
size and removal of most particles to 1 micron in size.
|
Vacuum Style and
Contact Cleaners
|
|
|
Mark I Vacuum Web and Sheet Cleaning System
|
|
The Mark I Web and Sheet Cleaning System
includes brushes and static control bars before and after the vacuum
slot. Removal of dust and dirt improves production speeds and lowers
the incidence of product quality defects.
An Ion-O-Vac’s is normally mounted where
material has more than 30 degrees of surface contact with a roller or
cylinder. This maximizes the cleaning effect of the high pressure
vacuum. The collector must be located in close proximity to the heads.
One sided or top and bottom web cleaning Contact
and non-contact configurations Brackets and ducting included
Micrometer adjustments for precisely locating the cleaner head over
the substrate Manual or optional pneumatic retraction systems to raise
and lower the heads Brushes slide in and out for easy replacement
Economical replacement brush pricing |
|
|
|
|
|
|
Ion-O-Vac Mark IV Rotary Brush Web and Sheet
Cleaning System
|
|
Ion-O-Vac Mark IV Sheet Cleaning Systems utilize the power of rotary
brush action to scrub the material surface, cleaning down to
5-microns. The scrubbing action of the Mark IV rotary brush is
designed for the toughest of materials that demand the cleanest of
surfaces.
Standard features include a
canister collector with cartridge filter, pre-filter and motor
starter, Ion-O-Vac head with rotary brush, micrometer adjustment for
raising and lowering the head(s), drive motor and speed control,
static eliminator and brackets. Systems can be configured to clean one
or both sides of the material. |
|
|
|
Neutro-Vac Web and Sheet Cleaning System
|
|
| Neutro-Vac utilizes a low velocity, high
volume vacuum system, which makes it ideal for installation over
unsupported webs, because the material will not be pulled to the
vacuum slot. The systems can be either non-contact (the material being
cleaned is not touched by brushes or other mechanical methods) or
contact style. Neutro-Vacs combine the power of a compressed air
blast, static eliminator and a high output exhaust head to agitate the
web, remove the static bond and evacuate the surface particulate. |
|
|
|
NWS Narrow Web Cleaning System
|
|
The NWS utilizes a
unique five-phase cleaning process. A static eliminator removes the
static charges bonding dust and dirt onto the web. A low pressure,
high volume air flow is applied to the web, circulating and vacuuming
particulate. Primary and sealing brushes are also used to enhance
cleaning effectiveness.
The NWS can be easily installed onto
any area of open web on most major narrow web presses and other narrow
web machinery. Three standard sized systems are available, 8",
12" and 18", with versions for cleaning one side and both
sides of the web. Because NWS systems are manufactured in standard
sizes, they are an economical investment with savings of up to 50% off
custom engineered systems.
|
|
|
|
Vac-N-Tac Comb. Web Cleaning System
|
|
SIMCO’s patent pending
Vac-N-Tac Narrow Web Cleaning Systems are precision engineered to
continuously clean paper, film or foil substrates of web thickness as
thin as .001".
Particles down to 1 micron in size are removed in a
3-stage process using static elimination, vacuum and contact cleaning
rolls (CCR). The Vac-N-Tac Web Cleaner offers better value and higher
performance than just contact cleaning systems, ultrasonic cleaners or
traditional vacuum collection. Specifically designed to fit into lines
with space constraints, the unit vacuum cleans the majority of
particles before the CCR cleans the web. Performance evaluations
reveal a cleaning efficiency of 97% of particles down to 10 micron in
size and removal of most particles to 1 micron in size. |
|
|
|
